0
Im пытается подключить модуль ESP12-E с дисплеем ILI9341 320 * 240 и считыватель RFID PN532 на той же шине SPI. Я назначил SS-контакты на разных GPIO.Несколько подчиненных SPI на ESP8266 - PN532 и ILI9341
Im не может связаться с обоими. Дисплей отлично работает в любых условиях. Но как только я общаюсь с ILI9341, PN532 перестает работать, и он не будет реагировать, пока я не перезапущу устройство, даже если я его повторно инициализирую.
Любая помощь будет высоко оценен Мой код:
#include <Wire.h>
#include <SPI.h>
#include <Adafruit_PN532.h>
#include <UTFT.h>
UTFT lcd(ILI9341_S5P,15,D1,D3);
// If using the breakout with SPI, define the pins for SPI communication.
#define PN532_SS (D4)
#define PN532_SCK (D5)
#define PN532_MOSI (D7)
#define PN532_MISO (D6)
// If using the breakout or shield with I2C, define just the pins connected
// to the IRQ and reset lines. Use the values below (2, 3) for the shield!
#define PN532_IRQ (2)
#define PN532_RESET (3) // Not connected by default on the NFC Shield
// Uncomment just _one_ line below depending on how your breakout or shield
// is connected to the Arduino:
// Use this line for a breakout with a SPI connection:
Adafruit_PN532 nfc(PN532_SCK, PN532_MISO, PN532_MOSI, PN532_SS);
// Use this line for a breakout with a hardware SPI connection. Note that
// the PN532 SCK, MOSI, and MISO pins need to be connected to the Arduino's
// hardware SPI SCK, MOSI, and MISO pins. On an Arduino Uno these are
// SCK = 13, MOSI = 11, MISO = 12. The SS line can be any digital IO pin.
//Adafruit_PN532 nfc(PN532_SS);
// Or use this line for a breakout or shield with an I2C connection:
//Adafruit_PN532 nfc(PN532_IRQ, PN532_RESET);
extern uint8_t BigFont[];
void setup(void) {
Serial.begin(115200);
Serial.println("Hello!");
nfc.begin();
uint32_t versiondata = nfc.getFirmwareVersion();
if (! versiondata) {
Serial.print("Didn't find PN53x board");
while (1); // halt
}
// Got ok data, print it out!
Serial.print("Found chip PN5"); Serial.println((versiondata>>24) & 0xFF, HEX);
Serial.print("Firmware ver. "); Serial.print((versiondata>>16) & 0xFF, DEC);
Serial.print('.'); Serial.println((versiondata>>8) & 0xFF, DEC);
lcd.InitLCD();
lcd.setColor (0, 0, 0);
lcd.fillRect(1,1,319,239);
lcd.setColor (255, 255, 255);
lcd.fillRect(100,100,220,140);
lcd.setFont (BigFont);
lcd.print(String("Scanning"),0,0);
// Set the max number of retry attempts to read from a card
// This prevents us from waiting forever for a card, which is
// the default behaviour of the PN532.
nfc.setPassiveActivationRetries(0xFF);
// configure board to read RFID tags
nfc.SAMConfig();
Serial.println("Waiting for an ISO14443A card");
}
void loop(void) {
boolean success;
uint8_t uid[] = { 0, 0, 0, 0, 0, 0, 0 }; // Buffer to store the returned UID
uint8_t uidLength; // Length of the UID (4 or 7 bytes depending on ISO14443A card type)
// Wait for an ISO14443A type cards (Mifare, etc.). When one is found
// 'uid' will be populated with the UID, and uidLength will indicate
// if the uid is 4 bytes (Mifare Classic) or 7 bytes (Mifare Ultralight)
success = nfc.readPassiveTargetID(PN532_MIFARE_ISO14443A, &uid[0], &uidLength,25);
if (success) {
Serial.println("Found a card!");
Serial.print("UID Length: ");Serial.print(uidLength, DEC);Serial.println(" bytes");
Serial.print("UID Value: ");
for (uint8_t i=0; i < uidLength; i++)
{
Serial.print(" 0x");Serial.print(uid[i], HEX);
}
Serial.println("");
// Wait 1 second before continuing
delay(1000);
}
else
{
// PN532 probably timed out waiting for a card
//Serial.println("Timed out waiting for a card");
}
}